网站首页-苏州迪泰新材料科研有限公司

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT 8416 a low viscosity surface insensitive cyanoacrylateadhesive. Product 8416 is specifically formulated to rapidlybond difficult substrates and to perform in lower humiditysituations. (Mil-A-46050C Type II, Class I).TYPICAL PROPERTIESEster Base ethyl-2-cyanoacrylateAppearance Clear, colourlessFlashpoint &gt;80°CDensity 1,05Shelf Life 12 months, unopenedViscosity (Brookfield) @ 25°C 1300-1500cP(Spindle 1, 20rpm)POLYMER PROPERTIESAppearance Clear, colourlessSoftening Point c. 125°CRefractive Index, nD20 1,45Full Cure Time 24 hoursSolubility DMF, acetonitrile, acetoneCURED SPEED VS. SUBSTRATEBalsa / Balsa &lt;5 secondsRubber / Rubber &lt;5 secondsNitrile / Nitrile &lt;5 secondsNeoprene / Neoprene &lt;5 secondsEPDM / EPDM &lt;5 secondsSteel / Steel 10-20 secondsPVC / PVC 3-10 secondsPolycarbonate / Polycarbonate 10-40 secondsCURED SPEED VS. GAPThe rate of cure will depend on the bondline gap. Thinbondlines result in high cure speeds, increasing the bond gapwill decrease the rate of cure.CURED SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps,applying activator to the surface will improve cure speed,However, this can reduce ultimate strength of the bond andtherefore testing is recommended to confirm effect.SHEAR STRENGTHGrit Blasted Steel &gt;15 N/mm²Etched Aluminium &gt;11 N/mm²Nitrile Rubber &gt;10 N/mm²Polycarbonate &gt;12 N/mm²ABS 6~18N/mm²PVC 6~18N/mm²DIRECTIONS FOR USEFor best results the surface must be clean and free fromoil ,grease, rust and other contamination. Best results withDEDT adhesive are obtained by using the minimum amount ofadhesive needed to fill the gap between the two matingsurfaces. Apply firm pressure to mated surfaces until adhesivesets.BLOOMING/CHLOROSISVapor generated by uncured liquid adhesive can be depositedon nearby surfaces leaving a white residue. The condition canbe reduced using one or more of the following methods:Clean with DEDT 755.Reduce quantity of the adhesive used.Increase the airflow.Speed the fixture/cure of the adhesive by using an accelerator.PRODUCT STORAGEStore product in the unopened container in a dry location.Optimal storage:2℃ to 8℃. Keep container tightly capped. Ifstored at low temperature, product must be allowed to returnto room temperature before use, This normally takes 8 to12hours.DISCLAIMERThe data contained within this Technical Data Sheet arefurnished for information only and are believed to be reliableat the time of issue. We cannot assume responsibility forresults obtained by others over whose methods we have nocontrol. It is the responsibility of the customer to determinethe products suitability for use. DEDT Limited and itsassociated companies accept no liability arising out of the useof this information or the products described herein.

DEDT 835瞬干胶

瞬干胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT 835 a high viscosity low-odour, low-bloom cyanoacrylate adhesive. The product has a rapid cure rate and issuitable for porous substrates or where gap fill may be required.TYPICAL PROPERTIESEster Base Alkoxy-ethyl cyanoacrylateAppearance Clear, colourlessFlashpoint &gt;81°CDensity 1.10Shelf Life 12 months, unopenedViscosity (Brookfield) @ 25°C 850-1250cPs(Spindle 1, 20rpm)POLYMER PROPERTIESAppearance Clear, colourlessSoftening Point c. 100°CRefractive Index, nD20 1,45Full Cure Time 24 hoursSolubility DMF, acetonitrile, acetoneCURED SPEED VS. SUBSTRATEBalsa / Balsa 15- 20 secondsRubber / Rubber &lt;7 secondsNitrile / Nitrile &lt;7 secondsNeoprene / Neoprene &lt;7 secondsEPDM / EPDM &lt;7 secondsSteel / Steel 20-40 secondsPVC / PVC 20-40 secondsPolycarbonate / Polycarbonate 20-50 secondsCURED SPEED VS. GAPThe rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gapwill decrease the rate of cure.CURED SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed,However, this can reduce ultimate strength of the bond and therefore testing is recommended to confirm effect.SHEAR STRENGTHGrit Blasted Steel &gt;14 N/mm²Etched Aluminium &gt;10 N/mm²Nitrile Rubber &gt;4 N/mm²Polycarbonate &gt;3 N/mm²Technical Data Sheet835ABS &gt;6N/mm²PVC &gt;2N/mm²DIRECTIONS FOR USEFor best results the surface must be clean and free from oil ,grease, rust and other contamination. Best results withDEDT adhesive are obtained by using the minimum amount of adhesive needed to fill the gap between the twomating surfaces. Apply firm pressure to mated surfaces until adhesive sets.PRODUCT STORAGEStore product in the unopened container in a dry location. Optimal storage:2℃ to 8℃. Keep container tightly capped.If stored at low temperature, product must be allowed to return to room temperature before use, This normally takes 8to12 hours.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliableat the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have nocontrol. It is the responsibility of the customer to determine the products suitability for use. DEDT Limited and itsassociated companies accept no liability arising out of the use of this information or the products described herein.

DEDT 1770处理剂

处理剂

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT activator 1770 is a single component non CFC solvent base product, formulated toprovide a faster cure on acicdic surfaces and cure excess DEDT cyanoacrylate adhesive outsidethe bond lines. The product is highly flammable.TYPICAL APPLICATIONSDEDT 1770 is used to increase the cure speed of DEDT cyanoacrylate adhesive. It can beeither pre-or post-applied to the bond. It is especially suited for post application on exposedcyanoacrylate adhesive outside of the bond line.POLYMER PROPERTIESSolvent AcetoneChemical Base Organic AcceleratorAppearance Clear to amberSpecific Gravity 0.79Viscosity (at 25°C) (mPa.s) 0.4Flash Point (TCC) °C -17Dry time (at 20°C) seconds &lt;30PRODUCT BENEFITS* Improves the gap filling capability of cyanoacrylate adhesive.* Reduce Fixture time.* Has zero ozone depletion potential.TYPICAL PERFORMANCEFixture time and cure speed achieved as a result of using DEDT 1770 depend on the adhesiveused and substrate bonded.HANDLING PROCEDURESDEDT 1770 is highly flammable.The solvent may effect certain plastics or coatings. It is recommended that the user check allsurfaces for compatibility before use.DIRECTIONS FOR USE1. Apply DEDT cyanoacrylate adhesive to one of the surfaces to be bond and assemble.2. Apply DEDT 1770 over all exposed cyanoacrylate adhesive by spray or by drop. Use oneLaboratory Data SheetA professional adhensive supplier DEDT New materials（HK）CO.,LTDdrop of activator per one drop of exposed adhesive.3. Apply the DEDT cyanoacrylate product immediately after drying but not more than 50seconds thereafter.4. Apply accelerator again if a delay of more than 45 seconds between original activation andadhesive application.PRODUCT STORAGEDEDT 1770 is classified as highly flammable and must be stored in an appropriate manner incompliance with relevant regulations. Do not store combustible materials. Optimal storage: 8℃to 21℃.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and arebelieved to be reliable at the time of issue. We cannot assume responsibility for results obtainedby others over whose methods we have no control. It is the responsibility of the customer todetermine the products suitability for use. DEDT Limited and its associated companies acceptno liability arising out of the use of this information or the products described herein.

DEDT AC9促进剂

处理剂

市场价:0.00

价格:0.00

DEDT 1050AB胶

AB胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT H-1050 is a toughened , medium high viscosity , rapid curing industrial grade epoxystructural adhesive with excellent strength. Once mixed , the two-component epoxy cures atroom temperature which provides high peel resistance and high shear strength to a wide varietyof materials including plastics , metals , glass and ceramics. It’s high transparency , highpermeability , and rapid curing at lower temperature characteristics , makes it suitable for manybonding applications.PROPERTIES OF UNCURED MATERIALResin HardenerChemical type Epoxy AmineAppearance Clear liquid Slight yellow liquidSpecific Gravity@25℃ 1.17 1.12Viscosity @25℃ , cps 12000+5000cps 12000+5000cpsFlash point(TOC) , ℃ &gt;90℃ &gt;200℃Mix Ratio (R : H) 1 : 1 (by weight)Working life @25℃ 5-8 min.Initial curing time , 5g@25℃ 15 min.PROPERTIES OF CURED MATERIALFully curing time @25℃ 3 days25℃/24hr 80℃/Water absorption rate , ℃/24hr 97℃/1.5hr%2.6 9.06 5.77Thermal degradation temperature , (TGA10°C/min) , °C 332Thermal expansion constant , (110~170°C) , μm/m/°C 210Thermal conductive constant , w/mK 0.3Hardness ASTM D-1706 , Shore D 84H-1050Technical data sheetGlass transition temperature , Tg , ℃ 52Volume resistivity, ASTM D257 5 x 1015Ω.cmSurface resistivity, ASTM D2575 x 1014ΩDielectric constant &amp; loss, 25°C, ASTM D150 ,measured at 100Hz 4.1(loss0.02)Bonding intensity , room temperature 7 days , JIS K6850 , Kg/cm² 207DIRECTION FOR USE1. For best performance surfaces should be clean and free of grease. Removal of surfacecontaminates such as paints , oxide films , oils , dust , mold release agents before bonding.2. Use gloves to minimize skin contact and keep the work environment in an good air flowingstatus.3. Mix thoroughly by weight in the proportions. Mix vigorously approximately 1~3 minutes afteruniform color is obtained. Keep parts from moving during cure. Contact pressure isnecessary.4. Excess uncured adhesive can be cleaned up with ketone type solvents.STORAGEOptimal storage is in a cool , dry location at a temperature between 8°C to 28°C. Shelf life canbe 1 year under 25℃ storage.NOTEThe data contained herein may be reported as a typical value and/or range (based on the mean value ±2standard deviations). Values are based on actual test data and are verified on a periodic basis. The datacontained herein are furnished for information only and are believed to be reliable. We cannot assumeresponsibility for the results obtained by others over whose methods we have no control. We recommend thateach prospective user test his proposed application before repetitive use.

DEDT3215

厌氧胶

市场价:0.00

价格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3215 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces.&nbsp;<h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves. &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; <h5>POLYMER PROPERTIES</h5>TypicalValue&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; RangeChemical Type&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; Dimethacrylate esterAppearance&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Blue liquidSpecific Gravity&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; 1.1Viscosity (at 25°C) (mPa.s)&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; 7000&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 5000 to 9000Flash Point (TCC) °C&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &gt;93&nbsp;<h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;Fixture time/Full cureSteel&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;30min/24hrsBrass&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;40min/24hrsZn Dichromate&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 50min/24hrs<h6>Stainless Steel&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;60min/24hrs</h6><h6>&nbsp;</h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1>&nbsp;</h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect.&nbsp;<h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m).&nbsp;&nbsp;TypicalValue&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; RangeBreakaway Torque&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp; 31&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 25~35Prevailing Torque&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp; 35&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 28~40&nbsp;<h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates.&nbsp;<h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint.&nbsp;PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container.&nbsp;DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.

DEDT3242

厌氧胶

市场价:0.00

价格:0.00

PRODUCT DESCRIPTIONDEDT 3242 is a single component anaerobic threadlocking material, which is thixotropic and developsmedium strength . The product cures when confined in the absence of air between close fitting metalsurfaces.TYPICAL APPLICATIONS*Prevents loosening and leakage of threaded fasteners.*Pump and motor mounting bolts.*Engine rocker nut*Situations were disassembly with hand tools is required.POLYMER PROPERTIESTypicalValue RangeChemical Type Dimethacrylate esterAppearance Blue liquidSpecific Gravity 1.05Viscosity(at 25°C)(mPa.s) 2000 1200 to 2800Flash Point(TCC) °C &gt;93CURE SPEED VS. SUBSTRATEThe rate of cure will depend on substrates involved.Substrate Fixture time/Full cureSteel 15min/24hrsBrass 20min/24hrsZn Dichromate 30min/24hrsStainless Steel 40min/24hrsCURE SPEED VS. BOND GAPThe rate of cure will depend on the bondine gap. The bondlines result in high cure speeds, increasing thebond gap will decrease the rate of cure.CURE SPEED VS. ACTIVATORWhere cure speed is unacceptably long due to large gaps, applying activator to the surface will improvecure speed, But may also impair overall adhesive performance and therefore testing is recommended toconfirm effect.CURE SPEED VS. TEMPERATUREThe rate of cure will depend on the ambient temperature. High temperature tend to increase the speedTYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts(N/mm²)TypicalValue RangeBreakaway Torque 19 14~25Prevailing Torque 8 4~11GENERAL INFORMATIONThis product is not recommended for use in pure oxygen rich systems and should not be selected as sealantfor chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check forcompatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect thecure and performance of the adhesive.This product may not be compatible with plastics,(particularly thermoplastic materials where stresscracking of plastic could result). Users are advised to confirm compatibility of the product with suchsubstrates.DIRECTIONS FOR USEFor best results, surfaces should be clean and free of grease. 3243 should be applied to the bolt in adequatequantity to fill all engaged threads. 3243 performs best in thin bond gaps, (0.05mm). Very large thread sizesmay create large gaps which will affect cure speed and strength. This product is designed to give controlledfriction, (torque/tension ratio), during assembly. In cnitical tightening applications this ratio should beconfirmed.PRODUCT STORAGEProduct should be stored in a cool, dry location in unopened containers at a temperature between containersat a temperature between 46℉ (8℃)and 82℉ (28℃)unless otherwise stated. To prevent contamination ofunused product, do not return any material to its original container.DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed tobe reliable at the time of issue. We cannot assume responsibility for results obtained by others over whosemethods we have no control. It is the responsibility of the customer to determine the products suitability foruse. DEDT Limited and its associated companies accept no liability arising out of the use of thisinformation or the products described herein.

DEDT3217

厌氧胶

市场价:0.00

价格:0.00

<h1>PRODUCT DESCRIPTION</h1>DEDT 3217 is a single component anaerobic threadlocking material, which is develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces.&nbsp;<h5>TYPICAL APPLICATIONS</h5>* Prevents loosening and leakage of threaded fasteners.* Cylinder liner studs.* Air compressor fasteners.* Refrigeration safety valves. &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; <h5>POLYMER PROPERTIES</h5>TypicalValue&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; RangeChemical Type&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; Dimethacrylate esterAppearance&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Red liquidSpecific Gravity&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; 1.1Viscosity (at 25°C) (mPa.s)&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; 7000&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 5000 to 9000Flash Point (TCC) °C&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &gt;93&nbsp;<h5>CURE SPEED VS. SUBSTRATE</h5>The rate of cure will depend on substrates involved.Substrate&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;Fixture time/Full cureSteel&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;30min/24hrsBrass&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;40min/24hrsZn Dichromate&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 50min/24hrs<h6>Stainless Steel&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;60min/24hrs</h6><h6>&nbsp;</h6><h6>CURE SPEED VS. BOND GAP</h6>The rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap will decrease the rate of cure.<h1>&nbsp;</h1><h1>CURE SPEED VS. ACTIVATOR</h1>Where cure speed is unacceptably long due to large gaps, applying activator to the surface will improve cure speed, But may also impair overall adhesive performance and therefore testing is recommended to confirm effect.&nbsp;<h6>CURE SPEED VS. TEMPERATURE</h6>The rate of cure will depend on the ambient temperature. High temperature tend to increase the speed.TYPICAL PROPERTIES(CURE)After 24hr at 22℃ on M10 steel nuts and bolts (N.m).&nbsp;&nbsp;TypicalValue&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; RangeBreakaway Torque&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp; 31&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 25~35Prevailing Torque&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp; 35&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 28~40&nbsp;<h1>GENERAL INFORMATION</h1>This product is not recommended for use in pure oxygen or rich systems and should not be selected as sealant for chlorine or other strong oxidizing materials.Where aqueous washing systems are used to clean the surfaces before bonding. It is important to check for compatibility of the washing solution with the adhesive. In some case, these aqueous washes can affect the cure and performance of the adhesive.This product may not be compatible with plastics, (particularly thermoplastic materials where stress cracking of plastic could result). Users are advised to confirm compatibility of the product with such substrates.&nbsp;<h1>DISASSEMBLY AND CLEANUP PRODUCT</h1>To aid in disassembly, DEDT anaerobic compounds can be weakened by heating to at least 260℃. Once disassembled ,cured adhesive can removed with DEDT Gasket Remover1790 by following instructions. A solvent wipe with an organic or petroleum solvent will remove uncured adhesive outside the joint.&nbsp;PRODUCT STORAGE Product should be stored in a cool, dry location in unopened containers at a temperature between c between 46℉ (8℃) to 82℉ (28℃) unless otherwise stated. To prevent contamination of unused product, do not return any material to its original container.&nbsp;DISCLAIMERThe data contained within this Technical Data Sheet are furnished for information only and are believed to be reliable at the time of issue. We cannot assume responsibility for results obtained by others over whose methods we have no control. It is the responsibility of the customer to determine the products suitability for use. DEDT New materials Limited and its associated companies accept no liability arising out of the use of this information or the products described herein.